Danh mục sản phẩm
Thẻ sản phẩm
Đầu nối ô tô
Ổ cắm hàng không
Bấm công tắc
Đầu nối hình tròn
Cáp kết nối
Kết nối
Cáp y tế tùy chỉnh
Ổ cắm DC
Công tắc điện tử
dây nịt dây điện EV
Dây nguồn nối dài
Đầu nối công nghiệp
khuôn ép
ép phun
Khai thác dây y tế
Cảm biến nhiệt độ NTC
Overmolded Cable Assemblies
Sản phẩm ép nhựa
Cáp dây nguồn
Bộ chuyển đổi phích cắm điện
Cáp cắm điện
Cảm biến nhiệt độ PT100
Công tắc vi mô SPST
Cảm biến nhiệt độ
Đầu dò cảm biến nhiệt độ
Cáp dữ liệu USB
Đầu nối dây
Dây nịt
Thiết bị đầu cuối dây
China Precision Micro Switch Manufacturer & Supplier
Category: Nhà cung cấp công tắc điện tử
Thẻ: Công tắc điện tử, Công tắc vi mô SPST
Definition of limit micro switch
A micro switch has a small contact spacing and a snap-action mechanism. The contact limit switch that performs the switch action with a specified stroke and force is covered by a shell, has an actuator on the outside, and has a small appearance. The figure below is an example of a typical micro switch structure. Micro switches are composed of 5 major components.
Micro limit switch Terminology:
■ General terms
(1) General terms
Micro switch: A switch with a contact structure that has a small contact gap and a snap-action mechanism, performs a switching action with a specified stroke and a specified force, is covered by a housing, and has a drive rod on the outside. (Hereinafter referred to as a switch) With contacts: Among switch types, compared with semiconductor switches with switching characteristics, the switch function is achieved by mechanical switching of contacts. Contact form: The electrical input and output circuits that constitute contacts according to various uses [shown in (16)].
Rated value: Generally refers to the value that serves as a guarantee benchmark for switch characteristics and performance, such as rated current, rated voltage, vân vân. The premise is specific conditions (type of load, current, voltage, frequency, vân vân.).
Resin fixing (molded terminal): After wiring the terminal part with a wire, the part is fixed by filling with resin to eliminate the exposed live parts and improve the drip resistance.
Vật liệu chống điện: Refers to the resistance value between non-connected terminals, between each terminal and a non-live metal part, and between each terminal and ground.
Chịu được điện áp: The critical value that does not cause insulation damage after applying high voltage to the specified measurement position for 1 minute.
Contact resistance: The resistance of the contact part of the contact, but generally refers to the resistance value including the conductor resistance of the spring and terminal part.
Vibration resistance: The vibration range in which the contact closed by vibration does not separate for more than the specified time when the micro switch is in use.
Shock resistance: Durable shock refers to the shock within the range that the micro switch will not be damaged by the mechanical shock during transportation or installation and meets the operating characteristics.
False operation shock? Refers to the shock range in which the contact closed by shock does not separate for more than the specified time when the micro switch is in use.
(2) Terms related to structure and construction
(3) Terms related to life
Mechanical life: The life of the switch when the contact is not energized and the overtravel (OT) is set to the specification value at the specified operating frequency.
Electrical life: The life of the switch when the rated load is connected to the contact and the overtravel (OT) is set to the specification value at the specified operating frequency.
(4) Standard test conditions
The test conditions of the switch are as follows.
Ambient temperature: 20±2℃, relative humidity: 65±5%RH, air pressure: 101.3kPa
(5) N level reference value
Indicates the failure level under a reliability of 60% (λ60).
λ60=0.5×10-6/times means that under a reliability of 60%, the failure rate is less than times.
(6) Contact shape and type
(7) Contact spacing
The contact spacing is specified as 0.25mm, 0.5mm, 1.0mm, and 1.8mm for four types of micro switches. The contact spacing is the target during design. When using, if the minimum contact spacing is required, please confirm and select. The general standard for the contact spacing is 0.5mm. For the same micro switch mechanism, the smaller the contact spacing, the smaller the MD, the higher the sensitivity, and the longer the mechanical life (lifespan), but it is disadvantageous in terms of DC breaking performance and vibration and shock resistance. The micro switch will wear out the contacts due to current switching, and the contact spacing will increase. As the MD increases, the sensitivity decreases. Vì thế, in order to achieve high sensitivity, when using a micro switch with a contact spacing of 0.25mm, the switching current must be kept small to reduce the contact loss caused by current switching. Products with large contact spacing have good vibration resistance, impact resistance and circuit breaking performance.
About this item
Package Content: 6 × Micro Limit Switch; Model No. : KW4-3Z-3
Hinge Lever Actuator, 1NO+1NC Contact Configuration.
Voltage & Current: AC 125V/250V 5A; Terminals: 3 Terminal
Switch Body Size: 2 x 1 x 0.7cm / 0.8″ x 0.4″ x 0.27″(L*W*H)
This Limit Switch can be used in various mechanical to control the position of moving parts of machines and plant.
Liên hệ chúng tôi
Chờ thư của bạn, chúng tôi sẽ trả lời bạn trong vòng 12 giờ với thông tin có giá trị bạn cần.
NHỮNG SẢM PHẨM TƯƠNG TỰ
China Online Custom Toggle Switch Type and Function
A toggle switch switches the circuit on or off by turning the switch handle, thereby achieving the purpose of switching the circuit. It's characterized by the presence of a manually operated handle or lever which controls the flow of electrical current from the power supply to a device (such as a household appliance).
NO/NC Slide Switches BBM, MBB & Maintained Switches
The domestic models of slide switches are: KB××, KZ××, KZX××, KHT××, KC××, KCX××, KZZ, vân vân. Those with Z are paper glue board type, those with C are porcelain type, those with H are epoxy glass cloth board type, and those with X are small band switches.
The application of the digital band switch is becoming more and more extensive, involving NC machine tools, NC equipment and precision instruments.
Rotary Switches, Rotary Limit – Isolator Switches
Rotary switches can be used to replace rotary pulse generators that mimic the function of conventional resistive potentiometers. These rotary switches are commonly used in human-machine interfaces on instrument front panels and audio-visual control panels. A rotary switch uses a quadrature optical encoder as a purely digital device instead of an analog potentiometer.
SPST Micro On/Off Toggle Switch for sale
Toggle switch is to turn on or off the circuit by toggling the switch handle, so as to achieve the purpose of switching the circuit. The commonly used varieties of toggle switches are unipolar double position, unipolar three position, bipolar double position and bipolar three position. It is generally used in low-voltage circuits and has the characteristics of flexible slider movement and stable and reliable performance.