Digitālā DS18B20 temperatūras sensora kabeļa komplekts

pēc pasūtījuma izgatavots ūdensizturīgs vairāku displeju esp32 LCD maizes panelis, arduino mega nano ds18b20 sensora kabeļa montāžas datu lapa.
DS18B20 ir digitāls temperatūras sensors ar plašu pielietojumu klāstu. Tas izvada digitālos signālus, un tam ir maza izmēra īpašības, zems aparatūras resursu patēriņš, spēcīga prettraucējumu spēja un augsta precizitāte.

DS18B20 temperature sensor features
1. Adopt single-wire interface method: DS18B20 temperature sensor only needs one wire to achieve two-way communication with the microprocessor.
2. Temperatūras mērīšanas diapazons: The temperature measurement range of DS18B20 temperature sensor Cable Assembly can reach -55℃~+125℃, and the error is ±0.4° in the range of -10℃ to +85℃.
3. Support multi-point networking function: multiple DS18B20 temperature sensors can be connected in parallel on a data line, up to 8 can be connected in parallel to achieve multi-point temperature measurement.
4. Working power supply: 3.0~5.5V/DC. The DS18B20 temperature sensor can be powered by an external independent power supply or a data line parasitic power supply.
5. The DS18B20 temperature sensor does not require any external components during application.
6. The temperature measured by the DS18B20 temperature sensor is transmitted serially in a 9 to 12-bit digital format.
7. Power-down protection function, the DS18B20 temperature sensor contains EEPROM inside. Digital conversion accuracy and alarm temperature can be set through the configuration register. The resolution and alarm temperature settings can still be saved after the DS18B20 temperature sensor is powered off.
8. The DS18B20 temperature sensor returns a 16-bit binary number representing the temperature value detected at this moment, and the high five digits represent positive and negative. If the high five bits are all 1, it means that the returned temperature value is a negative value. If the high five bits are all 0, it means that the returned temperature value is a positive value. The following 11 bits of data represent the absolute value of the temperature. After converting it to a decimal value, multiply it by 0.0625 to get the temperature value at this time.

Control method of temperature sensor DS18B20
DS18B20 has six control commands, as shown in Table 4.1:
Table 4.1 has six control commands for DS18B20
Instruction agreement code operation instructions:
Temperature conversion 44H: Start DS18B20 for temperature conversion;
Read temporary register BEH: Read temporary register 9-byte binary number;
Write temporary register 4EH: Write data into the TH and TL bytes of the temporary register;
Copy temporary register 48H: Write the TH and TL bytes of the temporary register to E2PROM;
Re-adjust E2PROM B8H: write the TH and TL bytes in the E2PROM to the temporary register TH and TL bytes;
Read the power supply mode B4H: Start DS18B20 to send the power supply mode signal to the main CPU;

Initialization of temperature sensor DS18B20
(1) First set the data line to high level “1”.
(2) Delay (the time requirement is not very strict, but it should be as short as possible)
(3) The data line is pulled to low level “0”.
(4) Delay of 750 microseconds (the time range can be from 480 uz 960 microseconds).
(5) The data line is pulled to high level “1”.
(6) Delay waiting: If the initialization is successful, a low level “0” returned by DS18B20 will be generated within 15 uz 60 microseconds. Its existence can be determined based on this status, but you should be careful not to wait indefinitely, otherwise the program will enter an infinite loop, so timeout control is required.
(7) If the CPU reads the low level “0” on the data line, it will still need to delay. The delay time is at least 480 microseconds from the high level sent out (from the time of step (5)).
(8) Pull the data line to high level “1” again and end.

Write operation of temperature sensor DS18B20
(1) The data line is first set to low level “0”.
(2) The delay time is determined to be 15 microseconds.
(3) Send bytes in order from low bit to high bit (only one bit is sent at a time).
(4) The delay time is 45 microseconds.
(5) Pull the data line to high level.
(6) Repeat the operations from (1) uz (6) until all bytes have been sent.
(7) Finally, pull the data line high.

Read operation of temperature sensor DS18B20
(1) Pull the data line high to “1”.
(2) Delay 2 microseconds.
(3) Pull the data line low to “0”.
(4) Delay 3 microseconds.
(5) Pull the data line high to “1”.
(6) Delay 5 microseconds.
(7) Read the status of the data line to get 1 status bit, and perform data processing.
(8) Delay 60 microseconds.

DS18B20 temperature sensor parasitic power supply mode
The parasitic power supply mode of the DS18B20 temperature sensor is shown in the figure below. In the parasitic power supply mode, the DS18B20 temperature sensor draws power from the signal line. When the signal line is high, electrical energy is stored in the internal capacitor. When the signal line is at a low level, the power on the capacitor is consumed, and the capacitor (parasitic power supply) is charged until the signal line reaches a high level.

Advantages of parasitic power supply:
1. No local power supply is required, and remote temperature measurement can be achieved.
2. Temperature measurement can be achieved with only one signal line, making the circuit simpler.

Disadvantages of parasitic power supply:
In order for the DS18B20 temperature sensor to perform accurate temperature conversion, the signal line must ensure that sufficient energy is provided during the temperature conversion. But when multiple DS18B20 temperature sensors are hung on the same signal line, the pull-up resistor alone cannot provide enough power, which will cause the DS18B20 temperature sensor to be unable to measure temperature or have a huge error.
Therefore, the parasitic power supply method is only suitable for use when measuring temperature with a single DS18B20 temperature sensor.